Resource Area

Centralised project documentation and downloadable technical assets

Resource Sections
    All Resources
    User Guides
      GAIA-FIELD Quick Start Guide
      GAIA-FIELD User Interface Guide
      GAIA-FIELD WiFi & Connectivity Guide
      GAIA-FIELD Creating and loading projects
      GAIA-FIELD Levelling Guide
      GAIA-FIELD Software Update Guide
      GAIA-FIELD Software Release Change Log
      GAIA-FIELD User Manual Overview _Oct_2026
    Video Tutorials
    Downloads

GAIA-FIELD WiFi & Connectivity Guide

User Guides

Overview of the connectivity options and configuration process for the GAIA-FIELD

Introduction

GAIA-FIELD can be controlled in three ways: through its own Wi-Fi access point, over a USB-C cable, or as a client on an existing Wi-Fi network. This guide explains each option and how to set it up from Settings > Connection in the GAIA-FIELD user interface.

For first-time connection, see the GAIA-FIELD Quick Start Guide. For the Home and Measure pages, see the GAIA-FIELD User Interface Guide.

Key Terms

Term

Meaning for GAIA-FIELD

Access point (AP) mode

GAIA-FIELD creates its own Wi-Fi network (e.g. GAIA-DEMO or GAIA <Serial>). Your phone, tablet or laptop joins it directly. No router or internet is involved.

Wi-Fi client mode

GAIA-FIELD joins an existing Wi-Fi network, such as a phone hotspot, office Wi-Fi or a Starlink router. Also called station mode.

USB-C Ethernet

A direct cable link. The USB-C port acts as a network connection (Ethernet over USB), so no drivers or software are needed.

SSID / network name

The name of a Wi-Fi network as it appears in your device's Wi-Fi list.

IP address

The address you type into your browser to open the GAIA interface, e.g. http://192.168.9.1.

DHCP

The service on a router or hotspot that automatically gives each connected device an IP address.

Personal hotspot

A phone sharing its mobile data connection as a Wi-Fi network.

Saved network

A Wi-Fi network GAIA-FIELD has joined before and stored, so it can reconnect automatically.

Wi-Fi radio

The Wi-Fi hardware in GAIA-FIELD. When disabled, both the access point and client connection are off.

RTK corrections

Positioning correction data, downloaded from the internet, that improves GNSS accuracy. Requires a configured correction service.

Live data upload

Sending measurement data from GAIA-FIELD to the internet during a survey. Requires an enabled data service.

GAIA-FIELD can run the access point and a Wi-Fi client connection at the same time. This lets a device stay connected directly to GAIA while GAIA uses another network for internet access.

Connection Methods at a Glance

Method

How to connect

GAIA-FIELD address

Internet

Best for

Access point

Join GAIA's Wi-Fi (e.g. GAIA <Serial>) on your device

http://192.168.9.1 (fixed)

No

Standard field use, first setup

USB-C Ethernet

Connect a USB-C cable from GAIA to your laptop or device

http://192.168.8.1 (fixed)

No

Large data file download, Wi-Fi problems, recovery

Wi-Fi client

GAIA-FIELD joins a hotspot, router or Starlink via Settings > Connection

Assigned by DHCP, shown under Addresses

Yes, via that network

RTK corrections, live data upload

NOTE: The access point and USB-C addresses never change. The Wi-Fi client address is set by the network, so check it on the Connection page each time GAIA-FIELD joins a new network.

  • Multiple smart devices can connect to a single GAIA-FIELD.
  • If using a smart phone on the access point, you may have to disable mobile data so the browser uses the GAIA Wi-Fi.
GAIA-FIELD Connectivity

The Connection Page

All connection settings are in Settings > Connection. The main menu is on the left of the screen, or at the bottom in mobile view. The page layout is the same on desktop and mobile; on mobile the sections stack in a single column.

GAIA-FIELD Connections Page 1

Status

The Status panel at the top shows the current state of each connection:

  • Wi-Fi status: Whether GAIA-FIELD is connected to a Wi-Fi network as a client (e.g. Not connected).
  • Connected network: The name of the network GAIA-FIELD has joined, if any.
  • Signal: Signal strength of that network.
  • Access point: GAIA-FIELD's own network name and whether it is on, e.g. GAIA-99 (on).

Addresses

This lists every address GAIA-FIELD can currently be reached on:

  • USB (usb0): The USB-C Ethernet connection.
  • Device access point (wlan0_ap): The access point address, 192.168.9.1.
  • Wi-Fi client address: Appears here once GAIA joins a network. Use this address to open the interface from other devices on that network.

Connect GAIA-FIELD to a Wi-Fi Network (Client Mode)

Use this to give GAIA-FIELD internet access through a phone hotspot, router or Starlink.

  1. Connect to GAIA-FIELD using the access point (http://192.168.9.1) or USB-C (http://192.168.8.1).
  2. Go to Settings > Connection.
  3. Under Available networks, click Scan for networks.
  4. Select your network from the list and enter its password.
  5. Wait for Wifi status to show connected. The network name and signal appear in the Status panel.
  6. The new Wi-Fi client IP address appears under Addresses. Note it down if you want to reach GAIA-FIELD from other devices on that network.

Hidden or out-of-range networks: Click Add network manually and enter the network name and password exactly as configured on the router or phone.

NOTE: If you are controlling GAIA from a device that is about to change networks, keep the access point on. You can then always return to http://192.168.9.1.

Saved Networks, Access Point and Wi-Fi Radio

Saved Networks

Networks GAIA has joined are listed under Saved networks. GAIA-FIELD uses these to reconnect automatically when the network is in range. If none have been added, the panel shows No saved networks.

Device Access Point

These settings control the network devices use to connect directly to GAIA-FIELD:

  • Network name: The Wi-Fi name GAIA broadcasts, e.g. GAIA-99.
  • Require a password: Tick to require a password to join. Recommended at all times.
  • Password: The password for the access point.
  • Save access point: Applies the name and password changes.
  • Turn access point off: Stops GAIA-FIELD broadcasting its own network - Caution! Connectivity is only possible via USB-C or Client Mode WiFi.

NOTE: Changing the access point name or password disconnects any device currently joined to it. Reconnect using the new details. The rear 'Connect' QR code will no longer match.

WARNING: Only turn the access point off if you can still reach GAIA-FIELD by USB-C or through a Wi-Fi client connection. Otherwise you will lose access to the interface.

GAIA-FIELD Connections Page 2

Wi-Fi Radio

Disable wifi turns off the Wi-Fi hardware entirely. This switches off both the device access point and any network connection. GAIA stays reachable over USB-C at http://192.168.8.1. Use this where wireless transmissions are not permitted.

Typical Setups

1. Direct to GAIA-FIELD

The phone or tablet joins GAIA-FIELD's access point for local control and live readings. There is no internet in this setup.

  • GAIA-FIELD: Access point on.
  • Phone: Mobile data off, Wi-Fi on, joined to GAIA <Serial>.
  • Open: http://192.168.9.1

2. Through a Phone Hotspot

GAIA-FIELD joins the phone's hotspot and uses its mobile data for RTK corrections. The same phone controls GAIA-FIELD.

  • Phone: Mobile data on, personal hotspot on.
  • GAIA: In Settings > Connection, scan and join the hotspot (e.g. Phone-Hotspot).
  • Open: The Wi-Fi client address shown under Addresses once GAIA has joined.

3. Together on a Shared Network (e.g. Starlink)

The phone and GAIA-FIELD join the same Wi-Fi network. GAIA-FIELD receives RTK corrections and uploads live data through that network.

  • Phone: Mobile data off, Wi-Fi on, joined to the shared network (e.g. Starlink).
  • GAIA: In Settings > Connection, scan and join the same network.
  • Open: The Wi-Fi client address shown under Addresses.

NOTE: Join the hotspot or shared network from GAIA-FIELD while connected via the access point or USB-C first. Then switch your phone to the new address.

RTK requires a configured correction service. Live upload requires an enabled data service. Network names shown are examples.

Troubleshooting

Problem

What to try

192.168.9.1 will not load

Check your device is joined to GAIA's Wi-Fi. On a phone, turn mobile data off. Confirm the Wi-Fi LED is lit.

Lost access after changing settings

Connect with USB-C and open http://192.168.8.1. Re-enable the access point or Wi-Fi radio.

GAIA-FIELD will not join a network

Re-check the password. Move closer to the router or phone. Use Add network manually for hidden networks.

Do not know GAIA-FIELD client address

Open the Connection page via the access point or USB-C and read it under Addresses.

No RTK corrections

Confirm GAIA-FIELD shows connected and the hotspot or router has internet. Check the correction service is configured.

Contact your SMG representative for any support or use our support form